The effect of unloading and ejection conditions on the properties of pharmaceutical tablets.

This study investigates decompression and ejection conditions on tablet characteristics by comparing compact densities and tensile strengths made using regular rigid dies and custom-built die systems that enable triaxial decompression. Die-wall pressure evolution during decompression and ejection stresses did not meaningfully impact the density and tensile strength of the materials tested: microcrystalline cellulose, crystalline lactose monohydrate, and mannitol. Furthermore, the apparent differences in tensile strength between rectangular cuboids and cylindrical compacts are unrelated to decompression and ejection conditions, but rather a consequence of their shapes and of the test configurations. This suggests that elastic and plastic deformations that may occur during decompression and ejection are not significantly influenced by die-wall pressure evolution. We thus conclude that while triaxial decompression and constraint-free ejection may allow the production of defect-free compacts for materials that otherwise are defect prone using a rigid die, they seem to pose no benefits when the materials already produce defect-free compacts using a rigid die.

Tensile Strength and Elastic Modulus of Gutta-percha Cones Disinfected with Sodium Hypochlorite at Different Immersion Times: An In Vitro Comparative Study.

Aim: The tensile strength and modulus of elasticity of gutta-percha cones can be chemically altered due to disinfectant solutions. Therefore, the aim of the present study was to compare tensile strength and elastic modulus of gutta-percha cones subjected to sodium hypochlorite (NaOCl) disinfection at different times. Materials and Methods: This in vitro and longitudinal experimental study consisted of 45 gutta-percha cones, divided equally into three groups: Group 1 (disinfection with 2.5% NaOCl), Group 2 (disinfection with 5.25% NaOCl), and control group. All groups were subdivided according to immersion times for 1, 5, and 10 minutes. Tensile strength and elastic modulus were measured with a universal testing machine. For comparing more than two independent groups, parametric analysis of variance test with Sheffe's post hoc was used and for multivariate analysis, and multivariate analysis of variance test based on Pillai's Trace was used. In all statistical analysis, a significance level P ≤ 0.05 was considered. Results: When comparing the tensile strength of gutta-percha cones, no significant differences were observed after being immersed at 1, 5, and 10 minutes in NaOCl 2.5% (P = 0.715) and 5.25% (P = 0.585). Regarding the elastic modulus, a significant decrease (P < 0.05) was observed in those that were immersed in NaOCl 2.5% and 5.25% for 1, 5, and 10 minutes. Furthermore, increased NaOCl concentration significantly reduced the elastic modulus (P < 0.001). However, there were no significant differences in tensile strength (P > 0.05) and elastic modulus (P > 0.05), when evaluating the interaction between NaOCl concentration and time. Conclusion: Increasing NaOCl concentration significantly reduced the modulus of elasticity without affecting the tensile strength of gutta-percha cones, regardless of immersion time. Furthermore, the interaction of time and NaOCl concentration did not significantly affect the tensile strength and elastic modulus.

Alternative strategies for the recombinant synthesis, DOPA modification and analysis of mussel foot proteins - A case study for Mefp-3 from Mytilus edulis.

Mussel foot proteins (Mfps) possess unique binding properties to various surfaces due to the presence of L-3,4-dihydroxyphenylalanine (DOPA). Mytilus edulis foot protein-3 (Mefp-3) is one of several proteins in the byssal adhesive plaque. Its localization at the plaque-substrate interface approved that Mefp-3 plays a key role in adhesion. Therefore, the protein is suitable for the development of innovative bio-based binders. However, recombinant Mfp-3s are mainly purified from inclusion bodies under denaturing conditions. Here, we describe a robust and reproducible protocol for obtaining soluble and tag-free Mefp-3 using the SUMO-fusion technology. Additionally, a microbial tyrosinase from Verrucomicrobium spinosum was used for the in vitro hydroxylation of peptide-bound tyrosines in Mefp-3 for the first time. The highly hydroxylated Mefp-3, confirmed by MALDI-TOF-MS, exhibited excellent adhesive properties comparable to a commercial glue. These results demonstrate a concerted and simplified high yield production process for recombinant soluble and tag-free Mfp3-based proteins with on demand DOPA modification.

A novel organic-inorganic matrix nanofiltration membrane for remediating copper with enhanced thermal stability and mechanical strength.

Membrane separation technology in the last 40 years has experienced impressive growth, displacing conventional separation processes due to inherent advantages such as less capital investment, and energy efficiency and the devices were simple, compact, and modular. In the current work, we aimed to synthesize a thin-sheet nanofiltration membrane using chitosan (CS), poly(vinyl) alcohol (PVA), and montmorillonite nanoclay (MMT) for copper removal from aqueous solution. Thermogravimetric analysis and differential scanning calorimetry were employed to evaluate the thermal stability of a novel organic-inorganic hybrid membrane. The tensile strength was measured over a wide range of temperatures and pressure to determine its stability. The surface and cross-section morphology of the membrane were studied through scanning electron microscopy. The prepared membrane was then tested for filtration efficiency by adjusting parameters such as pH, pressure, metal ion concentration, and membrane thickness. A mechanism was proposed to explain the hooking of copper ions with the as-prepared membrane after spectral images, such as EDAX and FT-IR, were compared both before and after filtration.

Physicochemical and sensorial properties of tomato leathers at different drying conditions.

Tomato leather as a healthy alternative to traditional fruit leathers was formulated. A tray dryer with changing temperature (50, 60, and 70°C) and relative humidity (5%, 10%, and 20%) was used to achieve the best product in terms of color, water distribution, lycopene content, mechanical, and sensorial properties. Color change was the highest at 70°C due to the Maillard reaction. Lycopene content was also the highest at 70°C. Time domain-NMR relaxometry showed that water distribution of all samples was homogeneous and similar to each other. Processing conditions affected mechanical properties significantly. The highest tensile strength was observed at 70°C, possibly due to the denatured proteins. Sensory analysis indicated better flavor development at 70°C, whereas overall acceptability of samples was higher at 50°C. The results of this study showed the main processing parameters of tomato leather with a minimal amount of ingredients, with acceptable mechanical and sensorial properties. PRACTICAL APPLICATION: Tomato leather was produced by using minimal amount of ingredients. Taste of the leather was found acceptable, as a salty snack food. Therefore, this product can be produced economically and it has a high potential to be consumed as an alternative to conventional fruit leathers.

The distance of insertion points from wound margins in interrupted and vertical mattress sutures influences the tensile load capacity: An in vitro experimental study.

AIM: To determine the tensile load capacity (TLC) and the tearing characteristics for interrupted and vertical mattress sutures with different insertion points from the wound margin, and the effect of the bite size when using vertical mattress sutures. MATERIALS AND METHODS: A total of 120 gingiva and lining mucosa samples obtained from pig jaws were divided into groups according to the suturing technique (interrupted and vertical mattress sutures), distance of the insertion points from the wound margin (margin, 1, 3, and 5 mm) and bite size (1, 3, and 5 mm). The TLC of the suture and the tearing characteristics were evaluated using a tensile tester device. RESULTS: The TLC was significantly higher for vertical mattress sutures than for interrupted sutures regardless of the distance of the insertion points from the wound margin (intergroup p < .001). This distance significantly influenced the TLC for vertical mattress sutures (p < .05) but not for interrupted sutures (p > .05). Testing the tearing characteristics revealed that no tissue tearing occurred in groups when the insertion points were more than 3 mm from the wound margin. CONCLUSION: The TLC is higher for vertical mattress sutures than for interrupted sutures, and it increases when the insertion points are farther from the wound margin.

Resistance of the fiber-derived geotextile from Typha domingensis submitted to field degradation.

Geotextiles made from plant fibers creates a suitable environment for plant growth as part of soil bioengineering techniques. The faster decomposition of plant fiber geotextiles compared to synthetic ones demands the use of composites that enhance their waterproofing and extend their durability in the environment. The objective of this work was to evaluate the resistance of a geotextile made with Thypha domingensis to degradation caused by climatic variables. Tensile strength tests were conducted in the laboratory in order to evaluate the degradation of geotextiles treated with single and double layers of waterproofing resin. Based on Scanning Electron Microscopy (SEM) images, it was verified that applying double layer of waterproofing resin delays the fibers degradation up to 120 days of exposure to the effects of climatic variables other than temperature. The maximum resistance losses due to the geotextile's exposure to degradation were statistically significant for all three treatments: control-without waterproofing resin, with one layer resin, and with two layers resin. Therefore, waterproofing resin, provides a long-term protective solution for geotextiles made from cattail fibers.

Effects of Different Sterilization Methods on Orthodontic Wires: An In Vitro Study.

Objective: The purpose of this study was to determine the effect of common methods of sterilization on the tensile strength of Beta titanium, Stainless steel, Australian Stainless steel, Copper Nickel-Titanium, and Nickel-Titanium wires. It also aimed to evaluate the changes in tensile strength values caused by repeated cycles of sterilization. Materials and Methods: A sample of 225 orthodontic wires, i.e., beta-titanium, stainless steel, Australian stainless steel, copper nickel-titanium, and nickel-titanium wires, were collected from different manufacturers. These wires were divided into three groups, which consists of Groups 1, 2, and 3. Four methods of sterilization used in this study were as follows: (i) autoclave (250°F for 20 min), (ii) dry heat sterilization (375°F for 20 min), (iii) ethylene oxide sterilization (54°C for 4 hrs), and (iv) 2.45% acidic glutaraldehyde (10 hrs). Results: The results of this study showed that there was increase in tensile strength of beta-titanium and nickel-titanium wires using autoclave and dry heat sterilization. No statistically significant difference in tensile strength of stainless steel and Australian stainless steel archwires. The tensile strength of copper nickel-titanium wires decreased following 0, 1, and 5 cycles of sterilization. Conclusion: The lack of statistically significant differences established in the study of new and sterilized orthodontic archwires gives us reason to conclude that the orthodontic arch wires can be sterilized because the sterilizing processes do not affect their tensile strength and the orthodontists could thus ensure the maximum safety of their patients.

Assessment of the Micro-Tensile Strength of the Composites for the Various Antioxidants: An In Vitro Study.

Introduction: The application of the antioxidants after the teeth are bleached has been advocated to fasten the restorative process post-bleaching. The motive of this study was to examine and assess the micro-tensile binding strength of bleached enamel to the resin using a variety of antioxidant solutions. Finding the reason for the tooth fracture was the secondary outcome measured. Materials and Methods: An in vitro study was planned with 100 human extracted teeth, with 20 in each group with one as controls and 4 others tested for the antioxidants sodium ascorbate, epigallocatechin gallate, chitosan, and proanthocyanidin application. The bond strength of bleached enamel to the resin was well as the failure type was assessed after the values were noted and compared using the ANOVA and Tukey's methods keeping P < 0.05 as significant. Results: Epigallocatechin gallate specimens displayed the maximum micro-tensile bond strength under the investigational circumstances, whereas controls displayed the lowest micro-tensile bond strength. There was statistical alteration in micro-tensile bond strengths between all the groups except between epigallocatechin gallate vs chitosan and sodium ascorbate vs proanthocyanidin. High statistical significance was seen between the control and the antioxidant groups as well as between sodium ascorbate and epigallocatechin gallate and chitosan. Conclusion: The antioxidant chemicals significantly augmented the bond strength of bleached enamel to the resin that had been bleached. Also, when compared to the other experimental groups, epigallocatechin gallate and chitosan treatment displayed the greatest mean bond strength values.

Cellulose acetate nanofiber modified with polydopamine polymerized MOFs for efficient removal of noxious organic dyes.

The need to effectively remove toxic organic dyes from aquatic systems has become an increasingly critical issue in the recent years. In pursuit of this objective, polydopamine (PDA)-binary ZIF-8/UiO-66 (MOFs) was synthesized and incorporated into cellulose acetate (CA), producing ZIF-8/UiO-66/PDA@CA composite nanofibers under meticulously optimized conditions. The potential of fabricated nanofibers to remove cationic methylene blue (MB) dye was investigated. Various analysis tools including FTIR, XRD, SEM, zeta potential, BET, tensile strength testing, and XPS were employed. Results revealed a substantial leap in tensile strength, with ZIF-8/UiO-66/PDA@CA registering an impressive 2.8 MPa, as a marked improvement over the neat CA nanofibers (1.1 MPa). ZIF-8/UiO-66/PDA@CA nanofibers exhibit an outstanding adsorption capacity of 82 mg/g, notably outperforming the 22.4 mg/g capacity of neat CA nanofibers. In binary dye systems, these nanofibers exhibit a striking maximum adsorption capacity of 108 mg/g, establishing their eminence in addressing the complexities of wastewater treatment. Furthermore, the adsorption data fitted to the Langmuir isotherm, and the pseudo-second-order kinetic model. The fabricated nanofiber demonstrates good reproducibility and durability, consistently upholding its performance over five cycles. This suite of remarkable attributes collectively underscores its potential as a robust, durable, and highly promising solution for the effective and efficient removal of pernicious MB dye, in the context of both water quality improvement and environmental preservation.

Process-Structure-Property Relationship Development in Large-Format Additive Manufacturing: Fiber Alignment and Ultimate Tensile Strength.

Parts made through additive manufacturing (AM) often exhibit mechanical anisotropy due to the time-based deposition of material and processing parameters. In polymer material extrusion (MEX), printed parts have weak points at layer interfaces, perpendicular to the direction of deposition. Poly(lactic acid) with chopped carbon fiber was printed on a large-format pellet printer at various extrusion rates with the same tool pathing to measure the fiber alignment with deposition via two methods and relate it to the ultimate tensile strength (UTS). Within a singular printed bead, an X-ray microscopy (XRM) scan was conducted to produce a reconstruction of the internal microstructure and 3D object data on the length and orientation of fibers. From the scan, discrete images were used in an image analysis technique to determine the fiber alignment to deposition without 3D object data on each fiber's size. Both the object method and the discrete image method showed a negative relationship between the extrusion rate and fiber alignment, with -34.64% and -53.43% alignment per extrusion multiplier, respectively, as the slopes of the linear regression. Tensile testing was conducted to determine the correlation between the fiber alignment and UTS. For all extrusion rates tested, as the extrusion multiplier increased, the percent difference in the UTS decreased, to a minimum of 8.12 ± 14.40%. The use of image analysis for the determination of the fiber alignment provides a possible method for relating the microstructure to the meso-property of AM parts, and the relationship between the microstructure and the properties establishes process-structure-property relationships for large-format AM.

A comparative study on tensile strength of various thermoplastic polymers sheets following thermoforming on a pre-treatment and post-treatment maxillary model of a patient: an in vitro study.

OBJECTIVES: Thermoplastic polymers show alteration in their mechanical properties after thermoforming on a dental model. The purpose of this in-vitro study was to evaluate the tensile strength of different thermoplastic polymer sheets thermoformed on a pre-treatment (moderate crowding) and post-treatment (well-aligned) maxillary model of a patient. MATERIALS AND METHODS: Forty maxillary models (Twenty Pre-treatment & twenty Post-treatment of uniform dimension) were made by duplicating them using alginate Hydrogum 5 (Zhermack). Samples were then divided into eight groups of 5 samples each. The thermoplastic sheets Imprelon® (Scheu-Dent), AVAC R® (Jaypee), Placa Crystal® (BioART), EZ-VAC® (3A Medes)-1.0 mm thick were thermoformed on these models respectively. The sample was retrieved using ceramic bur mounted on a straight hand-piece and subjected for testing using TINIUS Olsen 10ST micro universal testing machine and recorded. RESULTS: There was no statistically significant difference (P > .05) in tensile strength of thermoformed thermoplastic polymer sheets between pre-treatment and post-treatment maxillary model. Tensile strength of EZ-VAC (3A Medes) showed higher variation between pre-treatment and post-treatment maxillary model though it was found to be statistically insignificant (P > .05). Significant difference (P < .05) was seen between groups when they were compared separately among pre-treatment and post-treatment models. CONCLUSION: Placa Crystal (BioART) among the pre-treatment group, EZ - VAC (3A Medes) among the post-treatment group, showed highest tensile strength. CLINICAL RELEVANCE: Results of the study highlights the necessity to test materials in conditions which stands in accordance with the clinical scenario to a considerable extent and also emphasizes the need for further study in aligner.

Validation of a double-semicircular notched configuration for mechanical testing of orthodontic thermoplastic aligner materials.

The potential of using specimens with a double-semicircular-notched configuration for performing tensile tests of orthodontic thermoplastic aligner materials was explored. Unnotched and double-semicircular-notched specimens were loaded in tension using a universal testing machine to determine their tensile strength, while finite element analysis (FEA) and digital image correlation (DIC) were used to estimate stress and strain, respectively. The shape did affect the tensile strength, demonstrating the importance of unifying the form of the specimen. During the elastic phase under tension, double-semicircular-notched specimens showed similar behavior to unnotched specimens. However, great variance was observed in the strain patterns of the unnotched specimens, which exhibited greater chance of end-failure, while the strain patterns of the double-semicircular-notched specimens showed uniformity. Considerable agreement between the theoretical (FEA) and practical models (DIC) further confirmed the validity of the double-semicircular-notched models.

Effect of various disinfectant solutions on the tensile strength of gutta-percha using the rapid sterilization technique.

Context: Gutta-percha (GP) gets contaminated during handling. It becomes imperative to ensure GP is sterile before placement in root canal space. Aims: The aim of the study was to evaluate and compare the tensile strength of GP treated with four different disinfectant solutions: 3% sodium hypochlorite (NaOCl), amla juice (AJ), Aloe vera (AV) juice, and pancha tulsi (PT). Settings and Design: The study design was an in vitro study. Materials and Methods: Fifty GP cones with a size of 30 were procured from sealed packages in five different groups. Experimental groups were disinfected for 1 min with 3% NaOCl, AJ, AV, and PT except the control group. Tensile and Brinell Testing Machine is used to measure the tensile strengths of GP. Statistical Analysis Used: Results were subjected to statistical analysis using the Kruskal-Wallis test followed by Dunn's post hoc test. Results: The mean tensile strength values for Groups A, B, C, D, and E are 9.49 Mpa, 13.33 Mpa, 12.58 Mpa, 12.69 MPa, and 13.56 MPa, respectively. In the herbal disinfectant group, such as AJ, AV, and PT, the tensile strength was not significantly altered, whereas in the 3% NaOCl group, it was reduced considerably. Conclusions: AJ, AV juice, and PT as a GP disinfectant do not alter the tensile strength of GP cones.

Eco-Transformation of construction: Harnessing machine learning and SHAP for crumb rubber concrete sustainability.

Researchers have focused their efforts on investigating the integration of crumb rubber as a substitute for conventional aggregates and cement in concrete. Nevertheless, the manufacture of crumb rubber concrete (CRC) has been linked to the release of noxious pollutants, hence presenting potential environmental hazards. Rather than developing novel CRC formulations, the primary objective of this work is to construct an extensive database by leveraging prior research efforts. The study places particular emphasis on two crucial concrete properties: compressive strength (fc') and tensile strength (fts). The database includes a total of 456 data points for fc' and 358 data points for fts, focusing on nine essential characteristics that have a substantial impact on both attributes. The research employs several machine learning algorithms, including both individual and ensemble methods, to undertake a comprehensive analysis of the created databases for fc' and fts. In order to ascertain the correctness of the models, a comparative analysis of machine learning techniques, namely decision tree (DT) and random forest (RF), is conducted using statistical evaluation. Cross-validation approaches are used in order to address the possible issues of overfitting. Furthermore, the Shapley additive explanations (SHAP) approach is used to investigate the influence of input parameters and their interrelationships. The findings demonstrate that the RF methodology has superior performance compared to other ensemble techniques, as shown by its lower error rates and higher coefficient of determination (R2) of 0.87 and 0.85 for fc' and fts respectively. When comparing ensemble approaches, it can be seen that AdaBoost outperforms bagging by 6 % for both outcome models and individual decision tree learners by 17% and 21% for fc' and fts respectively in terms of performance. The average accuracy of AdaBoost algorithm for both the models is 84%. Significantly, the age and the inclusion of crumb rubber in CRC are identified as the primary criteria that have a substantial influence on the mechanical properties of this particular kind of concrete.

Empirical relation to evaluate blast induced crack development zone while using explosives of different detonation pressure in opencast bench blasting.

The optimum utilisation of explosive energy in the rock blasting operation is a prime challenge for the blast designers. The explosive energy in this operation is used for movement of burden. The optimum fracturing of the rock mass to meet the production demand takes place along tension. In the process of blasting, the detonation pressure of the explosives in the blasthole induces shock wave to the rock mass. The propagating shock wave is initially compressive in nature and becomes tensile after being reflected from the free face. The extent of tensile damage zone would give the optimum burden for blasting. The explosive properties along with the rock mass properties and charge configuration influences the extent of tensile damage zone. In this study, an empirical relation has been developed for estimation of blast induced tensile damage zone. The experimental trials were conducted at a coal mine using two different types of explosives for the validation of the developed empirical relation. The ground vibration predictors were developed using the data of experimental trials. The induced damage zone was computed using empirical relation proposed by Forsyth (1993) and developed ground vibration predictors. The estimated damage zone using developed empirical predictor and Forsyth relation were compared. The difference in the induced damage zone using two approaches is within 10%. The predicted values using developed empirical relation are accurate with RMSE value of 0.227 m. Hence, the developed empirical relation would be beneficial for estimation of blast induced crack zone.

Effect of 4-META on microtensile bond strength of cements to ceramics.

Background: This study assessed the effect of different concentrations of 4-methacryloyloxyethy trimellitate anhydride (4-META) added to silane on microtensile bond strength (µTBS) of light-cure and dual-cure resin cement to hybrid and zirconia-reinforced lithium silicate ceramics. Materials and Methods: This in vitro, experimental study was conducted on 32 Celtra Duo and 32 VITA Enamic ceramics bonded to Allcem Veneer light-cure and Allcem dual-cure resin cements using silane impregnated with 4-META in 0%, 2.5%, 5%, and 10 wt% concentrations in 16 groups (n = 4). The µTBS of specimens was measured by a universal testing machine and analyzed by the Kruskal-Wallis and Mann-Whitney tests, and the mode of failure was determined under a stereomicroscope and analyzed by the Chi-square test (alpha = 0.05). Results: The lowest mean µTBS was recorded in the Enamic ceramic group with 4-META (0%) bonded to dual-cure cement (14.26 MPa), and the highest mean µTBS was recorded in Enamic ceramic with 4-META (10%) bonded to light-cure cement (18.59 MPa) (P < 0.001). The µTBS of Celtra Duo was significantly higher than that of Enamic in bonding to light-cure cement using 4-META (2.5%) (P = 0.003). All failures (100%) were adhesive in most groups. The frequency of adhesive failure was the lowest (90%) in Celtra Duo bonded to dual-cure cement with 4-META (5%). Conclusion: According to the results of this pilot study, the addition of 4-META (10%) to silane caused a significant improvement in µTBS to light-cure cement. The addition of 4-META in all concentrations significantly improved the µTBS to Enamic ceramic in the use of dual-cure cement; however, it had no significant effect on µTBS of Celtra Duo. Nonetheless, the results should be interpreted with caution due to the relatively small sample size.

CHARACTERISATION OF RESORBABLE AND NON- RESORBABLE SUTURES COATED WITH Punica granatum SEED EXTRACT: AN in vitro PILOT STUDY.

BACKGROUND: In order to achieve uneventful and rapid healing of the tissues, a suture material should be biocompatible, easy to handle, sterile, and have good and uniform tensile strength. Hence, in the present study, characterization of the suture materials was done through a novel green chemistry approach using Punica granatum seed extract. MATERIALS AND METHODS: Ethanolic extract of P. granatum seed was prepared by dissolving 25 g of P. granatum seed powder with 100 mL of ethanol. The obtained extract was coated in silk and Vicryl suture material and was tested for its surface morphology (SEM), tensile strength, anti-microbial activity, biocompatibility, and wound healing potential. RESULTS: Silk and Vicryl sutures coated with P. granatum seed extract showed the uniform coating and deposition of extract with sustaining integrity. Vicryl suture coated with the extract had good tensile strength and antimicrobial activity. The in vitro scratch assay and biocompatibility test showed that the P. granatum seed extract had excellent wound healing potential and can be used without any effect on the viability of the normal cells. CONCLUSION: Within the limitations of the study it can be concluded that P. granatum seed extract coated Vicryl sutures had good tensile strength and anti-microbial activity. P. granatum seed extract also showed excellent biocompatibility and wound healing potential.

Study on the Mechanical Properties of Two General-Purpose Cement-Lime Mortars Prepared Based on Air Lime.

It is believed that the use of mortars based on air lime in the construction and renovation of brick buildings has a number of advantages, especially those closely related to the durability and strength of the structure. However, there is still a noticeable difference in the mechanical properties of these materials. This research investigated the mechanical characteristics of a mixed cement-lime mortar with the two most popular proportions of an air lime, cement, and sand mix: 1:1:6 and 1:2:9 (by volume). Mechanical tests were performed on standard and non-standard samples to assess compressive strength, tensile strength, flexural strength, and fracture energy. The obtained results indicate the possibility of using these mixtures in modern masonry construction, as well as in the aspect of sustainable development. Additionally, lime mortar with a higher lime content can be used in non-load-bearing walls and in renovation and repair works.

Effect of Steel Fibers on Tensile Properties of Ultra-High-Performance Concrete: A Review.

Ultra-high-performance concrete (UHPC) is an advanced cement-based material with excellent mechanical properties and durability. However, with the improvement of UHPC's compressive properties, its insufficient tensile properties have gradually attracted attention. This paper reviews the tensile properties of steel fibers in UHPC. The purpose is to summarize the existing research and to provide guidance for future research. The relevant papers were retrieved through three commonly used experimental methods for UHPC tensile properties (the direct tensile test, flexural test, and splitting test), and classified according to the content, length, type, and combination of the steel fibers. The results show that the direct tensile test can better reflect the true tensile strength of UHPC materials. The tensile properties of UHPC are not only related to the content, shape, length, and hybrids of the steel fibers, but also to the composition of the UHPC matrix, the orientation of the fibers, and the geometric dimensions of the specimen. The improvement of the tensile properties of the steel fiber combinations depends on the effectiveness of the synergy between the fibers. Additionally, digital image correlation (DIC) technology is mainly used for crack propagation in UHPC. The analysis of the post-crack phase of UHPC is facilitated. Theoretical models and empirical formulas for tensile properties can further deepen the understanding of UHPC tensile properties and provide suggestions for future research.